Ametek EC1000S Скачать руководство пользователя страница 12

Страница: 12 / 291

User Manual

EC1000S

！



Do not modify this product.

Absolutely never modify this product, as this may cause new hazards and may disqualify this product from

repair in case of failure.



Prevention of electrical shock due to output voltage

The maximum output of the EC1000S is



400 V.

Carefully operate the EC1000S to avoid electrical shock.

Directly touching the output or changing cable connections while output is on may cause electrical shock.



Safety-related symbols

The general definitions of the safety-related symbols used on this product and in the instruction manual are

provided below.

Instruction Manual Reference Symbol

This symbol is displayed to alert the user to potential danger and refer him/her to the

instruction manual.

Electric Shock Danger Symbol

This symbol indicates locations that present a risk of electric shock under specific

conditions.

Protective Ground-Terminal Symbol

This symbol identifies a pin that must be grounded to avoid electric shock.

Before operating the device, be sure to safely implement grounding according to

local electrical safety codes.

Warning Symbol

This symbol indicates information for avoiding danger to human life or bodily injury

while handling this product.

Caution Symbol

This symbol indicates information for preventing damage to the product when

handling it.



Other symbols

This symbol indicates the “on” position of the power switch.

This symbol indicates the “off” position of the power switch.

This symbol indicates that the external conductor of the connector is connected to the case.

This symbol indicates that the external conductor of the connector is connected to the signal ground.



Waste disposal

To help ensure environmental protection, please note the following precautions regarding disposal of this

product.

CAUTION

WARNING

Содержание EC1000S




































































































































































































































































































Результаты поиска

Содержание EC1000S

Отзывы:

Похожие инструкции для EC1000S

Бренды по названию

Популярные бренды

Ametek EC1000S, Руководство пользователя

Результаты поиска

Содержание EC1000S

Отзывы:

Похожие инструкции для EC1000S

Бренды по названию

Популярные бренды