Amazone Precea 4500-2 Скачать руководство пользователя страница 66

Страница: 66 / 256

Designation

Function

Tractor control unit

Green

Section

Extend

Retract

Double-acting

Track marker

Lifting

Single-acting

Frame ballasting

Increase

Reduce

Double-acting

Beige

Filling auger

Switching on

Single-acting

Red

Fan hydraulic motor

Switching on

Single-acting

Pressure relief through pressureless return flow

WARNING

Risk of injury or even death

If the hydraulic hose lines are incorrectly
connected, the hydraulic functions may be
faulty.

When coupling the hydraulic hose lines,
observe the coloured markings on the
hydraulic plugs.

IMPORTANT

Implement damage due to insufficient
hydraulic oil return flow

Only use DN16 lines for the pressureless
hydraulic oil return flow.
Select short return paths.
Connect the pressureless hydraulic return
flow correctly.
Install the supplied coupling sleeve on the
pressureless hydraulic oil return.

Depressurise the hydraulic system between the
tractor and the implement using the tractor control
unit.

Clean the hydraulic plugs.

6 | Preparing the machine

Coupling the implement

MG6149-EN-GB | J.1 | 18.10.2022 | © AMAZONE

Содержание Precea 4500-2

































































































































































































































































Результаты поиска

Содержание Precea 4500-2

Отзывы:

Бренды по названию

Популярные бренды

Amazone Precea 4500-2, Оригинальное руководство по эксплуатации

Результаты поиска

Содержание Precea 4500-2

Отзывы:

Бренды по названию

Популярные бренды