manualshive.com logo in svg

Amazone Precea 4500-2, Оригинальное руководство по эксплуатации

Поделиться
Скачать
Amazone Precea 4500-2 Скачать руководство пользователя страница 242

10.4 Cleaning the implement

 

 

IMPORTANT 

 

 

Risk of machine damage due to cleaning
jet of the high-pressure nozzle

Never direct the cleaning jet of the
high-pressure cleaner or hot water
high-pressure cleaner onto the marked
components.
Never aim the cleaning jet of high-pressure
cleaners or hot water high-pressure
cleaners on electrical or electronic
components.
Never aim the cleaning jet of the high
pressure cleaner directly on lubrication
points, bearings, rating plates, warning
signs, and stickers.
Always maintain a minimum distance of
30 cm between the high-pressure nozzle
and the implement.
Do not exceed a water pressure of 120 bar.

 

CMS-I-00002692

 

Clean the machine with a high-pressure cleaner
or a hot water high-pressure cleaner.

CMS-T-00000593-F.1

10 | Repairing the machine

Cleaning the implement 

MG6149-EN-GB | J.1 | 18.10.2022 | © AMAZONE

236

Содержание Precea 4500-2

































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды