manualshive.com logo in svg

Amazone Precea 4500-2, Оригинальное руководство по эксплуатации

Поделиться
Скачать
Amazone Precea 4500-2 Скачать руководство пользователя страница 114

13. Remove the cotter pin 

3

.

14. Remove the washer 

2

.

15. Remove the gear wheel 

1

.

16. Take the desired gear wheel from the parking

position.

17. Put the removed gear wheel in the parking

position.

18. Install the desired gear wheel on the drive shaft.

19. Install the washer.

20. Install the cotter pin.

CMS-I-00002652

21. Actuate the lever 

1

.

The drive chain will be tightened.

22. Hold the lever.

CMS-I-00002651

23. Close the cover 

1

 against the spring pressure.

24.

To lock the cover,

Continue actuating the lever 

3

.

The cover will be locked on the chain tensioner

2

.

CMS-I-00002647

6 | Preparing the machine

Preparing the implement for operation 

MG6149-EN-GB | J.1 | 18.10.2022 | © AMAZONE

108

Содержание Precea 4500-2

































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды