manualshive.com logo in svg

Amazone Precea 4500-2, Оригинальное руководство по эксплуатации

Поделиться
Скачать
Amazone Precea 4500-2 Скачать руководство пользователя страница 187

10-amp fuse

Protected rows

F1

Row 1 to 4

F2

Row 5 to 8

F3

Row 8 to 12

1.

Clean the singling unit.

2.

Check the singling disc for ease of movement.

3.

Replace defective fuses.

1.

Remove the defective shear pin 

2

.

2.

Remove the defective shear pin from the drive

shaft 

3

.

3.

Clean the singling unit.

4.

Check the singling disc for ease of movement.

5.

Install the new shear pin 

1

.

CMS-I-00002696

Fill level in the singling unit housing is too high

The scraper removes excess seed from the singling
disc. If the brushes of the filling block are worn, the

seed does not flow back into the storage area 

2

within the filling block.

To replace the defective filling block,

see "Changing the singling disc"

or

contact your specialist workshop.

CMS-I-00005635

CMS-T-00008170-A.1

8 | Eliminating faults

 

MG6149-EN-GB | J.1 | 18.10.2022 | © AMAZONE

181

Содержание Precea 4500-2

































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды