manualshive.com logo in svg

Amazone Precea 4500-2, Оригинальное руководство по эксплуатации

Поделиться
Скачать
Amazone Precea 4500-2 Скачать руководство пользователя страница 145

6.5.21 Adjusting the fertiliser application point

Use the switch 

3

 to change the fertiliser application

point between the fertiliser coulter 

2

 or the seed bed

placement 

1

.

3

2

1

CMS-I-00007256

To select the fertiliser application point,

set the lever 

1

 to the desired position.

The lever engages perceptibly.

1

CMS-I-00007258

6.5.22 Adjusting the frame ballasting

The hydraulically actuated frame ballasting 

1

 is

supported on the lower links and transfers the weight
from the tractor to the implement frame. As a result,
there is an additional load on the precision airplanter
and the placement depth can be maintained even
under difficult operating conditions.

For maximum effect of the frame ballasting, the
implement must be coupled to the highest top link
point on the tractor side.

CMS-T-00010605-B.1

CMS-T-00002219-E.1

6 | Preparing the machine

Preparing the implement for operation 

MG6149-EN-GB | J.1 | 18.10.2022 | © AMAZONE

139

Содержание Precea 4500-2

































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды