manualshive.com logo in svg

Amazone Precea 4500-2, Оригинальное руководство по эксплуатации

Поделиться
Скачать
Amazone Precea 4500-2 Скачать руководство пользователя страница 116

7.

To make the chain lock 

4

 accessible,

turn the drive wheel 

1

 clockwise.

8.

Remove the clamping ring 

3

.

9.

Remove the gear wheel Z=15.

10. Install the gear wheel Z=30.

11. Install the chain extension.

12. Put the gear wheel 

2

 in the chain.

13. Install the gear wheel on the drive shaft.

14. Install the clamping ring.

CMS-I-00002657

15.

To tighten the drive chain,

put the tension spring 

2

 around the retaining pin

3

.

CMS-I-00002650

16.

To ensure that the tightened drive chain 

1

runs on all of the gear wheels,

turn the drive wheel.

CMS-I-00002648

6 | Preparing the machine

Preparing the implement for operation 

MG6149-EN-GB | J.1 | 18.10.2022 | © AMAZONE

110

Содержание Precea 4500-2

































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды