manualshive.com logo in svg

Amazone Precea 4500-2, Оригинальное руководство по эксплуатации

Поделиться
Скачать
Amazone Precea 4500-2 Скачать руководство пользователя страница 208

10.1.5 Checking and replacing the closer discs on the PreTeC mulch seeding coulter

INTERVAL

Every 100 operating hours

or

Every 3 months

1.

Determine the diameter of the closer discs.

2.

If the diameter of the closer discs is smaller than
180 mm,

replace the closer discs in pairs.

3.

Loosen and remove the bolts 

2

.

4.

Replace worn closer discs 

1

 with new closer

discs.

5.

Put on and tighten the bolts.

CMS-I-00005666

10.1.6 Checking and replacing the rigid cutting disc on the PreTeC mulch seeding coulter

INTERVAL

1.

Determine the cutting disc diameter.

2.

If the diameter of the cutting discs is less than
320 mm,

replace the worn cutting discs 

1

.

3.

Remove the bolts 

2

.

4.

Replace worn cutting discs with new cutting
discs.

5.

Install the bolts.

1

2

CMS-I-00005361

CMS-T-00008304-C.1

CMS-T-00007650-C.1

10 | Repairing the machine

Maintaining the machine 

MG6149-EN-GB | J.1 | 18.10.2022 | © AMAZONE

202

Содержание Precea 4500-2

































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды