manualshive.com logo in svg

Amazone Precea 4500-2, Оригинальное руководство по эксплуатации

Поделиться
Скачать
Amazone Precea 4500-2 Скачать руководство пользователя страница 200

9.12 Uncoupling the ISOBUS or control computer

1.

Unplug the connector of the ISOBUS line 

1

 or

the control computer line 

2

.

2.

Protect the plug with a dust cap.

3.

Hang the plug in the hose cabinet.

1

2

CMS-I-00006891

9.13 Disconnecting the hydraulic hose lines

1.

Secure the tractor and implement.

2.

Put the control lever on the tractor control unit in
float position.

3.

Disconnect the hydraulic hose lines 

1

.

4.

Put the dust caps on the hydraulic sockets.

1

CMS-I-00001065

5.

Hang the hydraulic hose lines 

1

 in the hose

cabinet.

1

CMS-I-00001250

CMS-T-00006174-D.1

CMS-T-00000277-E.1

9 | Parking the machine

Uncoupling the ISOBUS or control computer 

MG6149-EN-GB | J.1 | 18.10.2022 | © AMAZONE

194

Содержание Precea 4500-2

































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды