manualshive.com logo in svg

Amazone Precea 4500-2, Оригинальное руководство по эксплуатации

Поделиться
Скачать
Amazone Precea 4500-2 Скачать руководство пользователя страница 202

9.16 Uncoupling the universal joint shaft

1.

Remove the safety chain 

2

 from the tractor.

2.

Release the lock of the universal joint shaft 

1

.

3.

Pull off the universal joint shaft from the tractor
PTO shaft.

1

2

CMS-I-00001069

4.

Put the universal joint shaft 

1

 into the parking

position with the rubber strap 

2

.

2

1

CMS-I-00001935

9.17 Conserving the drive shaft

To ensure that the drive shafts can be smoothly
telescoped,

seal the shafts with a non-adhesive conservation
agent after washing.

CMS-I-00002825

CMS-T-00001843-B.1

CMS-T-00003870-A.1

9 | Parking the machine

Uncoupling the universal joint shaft 

MG6149-EN-GB | J.1 | 18.10.2022 | © AMAZONE

196

Содержание Precea 4500-2

































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды