ALLIANCE ST3LXFSP401NW22 Скачать руководство пользователя страница 8

Страница: 8 / 102

802953

Control Identification

Select Cycle Pads

SELECT CYCLE pads are used to select the specific

washer cycle. These pads include NORMAL 90,

NORMAL 60, NORMAL 40, PERM PRESS 60,

DELICATES 30 and DELICATES COLD. These pads

allow the user to select a cycle other than the default

cycle (PERM PRESS 60). The SELECT CYCLE

keypads are not active after the first fill step of the

cycle. The selected cycle is indicated by the light

(LED) on the pad. Pressing the flashing START pad

will confirm the selection and the cycle will begin.

When the card reader is used, pressing the START pad

will start the cycle and deduct the vend price from the

card.

NOTE: The number on each keypad corresponds

to the wash temperature in °C.

The SELECT CYCLE pads are used in various

combinations for programming cycles, retrieving audit

information, running diagnostic tests, and other

operations. These instructions cover the manual

programming and data retrieval options.

START Keypad

The START keypad is used to start the washer after the

full vend price has been satisfied.

Soil Level Pad

The SOIL LEVEL pad is used to select cycle modifier

options. Option A is the default and indicates no cycle

modifiers are active. Options B and C can be

programmed to offer extra features for an added vend

price. Features available include an added prewash,

extra wash time, an added extra rinse, and a warm

rinse temperature.
For details on programming the Soil Level option,

refer to

Programming Control

NORMAL 90

NORMAL 60

NORMAL 40

PERM PRESS 60

DELICATES 30

DELICATES COLD
(temperature of
water from tap)

FLW21R

FLW22R

FLW23R

FLW24R

FLW25R

FLW26R

START

SOIL LEVEL

FLW14R

FLW27R

Содержание ST3LXFSP401NW22







































































































Результаты поиска

Содержание ST3LXFSP401NW22

Отзывы:

Похожие инструкции для ST3LXFSP401NW22

Бренды по названию

Популярные бренды

ALLIANCE ST3LXFSP401NW22, Руководство по программированию

Результаты поиска

Содержание ST3LXFSP401NW22

Отзывы:

Похожие инструкции для ST3LXFSP401NW22

Бренды по названию

Популярные бренды