ALLIANCE ST3LXFSP401NW22 Скачать руководство пользователя страница 101

Страница: 101 / 102

802953

Communications Mode

Infra-red Communications

The Infra-red Communications feature allows the

washer control to communicate with an external

device. The washer control can be programmed and

have its data read without using the keypad. It may

also be used to start and stop various diagnostic tests.

How to Begin Communications with An
External Device

The control will go blank and the display will show

“

-C-

” until the communication is complete. If an error

occurs that terminates communication, the display will

show “

EIXX

” (“

” represents the error code).

NOTE: The Infra-red Communications option

must be turned on. Refer to

option 31

Programming Control

Card Reader Communications
(Card Models Only)

The Card Reader Communications feature allows the

washer control to communicate with the card reader.

The washer control can be programmed for a limited

number of options and have its data read without using

the keypad.

Network Communications

The Network Communications feature allows the

washer control to communicate with a network. The

washer control can be programmed and have its data

read without using the keypad.

Содержание ST3LXFSP401NW22







































































































Результаты поиска

Содержание ST3LXFSP401NW22

Отзывы:

Похожие инструкции для ST3LXFSP401NW22

Бренды по названию

Популярные бренды

ALLIANCE ST3LXFSP401NW22, Руководство по программированию

Результаты поиска

Содержание ST3LXFSP401NW22

Отзывы:

Похожие инструкции для ST3LXFSP401NW22

Бренды по названию

Популярные бренды