ALLIANCE ST3LXFSP401NW22 Скачать руководство пользователя страница 69

Страница: 69 / 102

Programming Control

802953

22. Special Vend D Days Enable

“SPd-”

This option allows the owner to enable or disable a

fourth special vend.
Special Vend D can be programmed using an external

device or network.

How to Program Special Vend D Days
Enable

1. Control must be in Manual Mode. Refer to

Entering the Manual Mode

2. Press the NORMAL 40 ( ) or the DELICATES

COLD ( ) keypad until “

Prog

” appears in the

display. Press the START (enter) keypad and

“

AtS1

”

will appear in the display.

3. Press the NORMAL 40 ( ) or the DELICATES

COLD ( ) keypad to scroll through the

programmable options until “

SPd-

” appears in

the display.

4. When “

SPd-

” appears in the display, press the

START (enter) keypad. The current Special Vend

D Days Enable status will appear in the display.

“

” = Option Enabled

“

oFF

” = Option Disabled (factory default

setting)

5. Press the NORMAL 40 ( ) or the DELICATES

COLD ( ) keypad to change the current status.

6. Press the START (enter) keypad when the correct

status appears in the display. The next option,

“

CnP-

”, will appear in the display.

NOTE: To program

“CnP-”

(Cycle Modifier

Programming), refer to

option 23

. To program

other options, refer to the appropriate section.

How to Exit Programming Feature

Press the DELICATES 30 (<) keypad until the control

returns to Ready Mode.

Содержание ST3LXFSP401NW22







































































































Результаты поиска

Содержание ST3LXFSP401NW22

Отзывы:

Похожие инструкции для ST3LXFSP401NW22

Бренды по названию

Популярные бренды

ALLIANCE ST3LXFSP401NW22, Руководство по программированию

Результаты поиска

Содержание ST3LXFSP401NW22

Отзывы:

Похожие инструкции для ST3LXFSP401NW22

Бренды по названию

Популярные бренды