ALLIANCE ST3LXFSP401NW22 Скачать руководство пользователя страница 34

Страница: 34 / 102

Programming Control

802953

8. OPL Mode “oPL”

This option allows the owner to enable or disable the

OPL Mode in which no vend price needs to be

satisfied to operate the machine.

How to Program the OPL Mode

1. Control must be in Manual Mode. Refer to

Entering the Manual Mode

2. Press the NORMAL 40 ( ) or the DELICATES

COLD ( ) keypad until “

Prog

” appears in the

display. Press the START (enter) keypad and

“

AtS1

” will appear in the display.

3. Press the NORMAL 40 ( ) or the DELICATES

COLD ( ) keypad to scroll through the

programmable options until “

oPL

” appears in the

display.

4. When “

oPL

” appears in the display, press the

START (enter) keypad. The current OPL Mode

Enable/Disable status will appear in the display.

“

” = Option Enabled

“

oFF

” = Option Disabled (factory default

setting)

5. Press the NORMAL 40 ( ) or the DELICATES

COLD ( ) keypad to change the current status.

6. Press the START (enter) keypad when the

desired status appears in the display. The next

option, “

AUd

”, will appear in the display.

NOTE: To program

“AUd”

(Audio Signal), refer to

option 9

. To program other options, refer to the

appropriate section.

How to Exit Programming Feature

Press the DELICATES 30 (<) keypad until the control

returns to Ready Mode.

Содержание ST3LXFSP401NW22







































































































Результаты поиска

Содержание ST3LXFSP401NW22

Отзывы:

Похожие инструкции для ST3LXFSP401NW22

Бренды по названию

Популярные бренды

ALLIANCE ST3LXFSP401NW22, Руководство по программированию

Результаты поиска

Содержание ST3LXFSP401NW22

Отзывы:

Похожие инструкции для ST3LXFSP401NW22

Бренды по названию

Популярные бренды