ALLIANCE ST3LXFSP401NW22 Скачать руководство пользователя страница 100

Страница: 100 / 102

802953

Power Fail Recovery

The Power Fail Recovery feature allows the cycle

status to be saved in memory in the event of a power

failure.
If the power failure lasted less than 30 seconds and the

door is locked, the cycle will resume without requiring

the user to press the START (enter) keypad to restart.
If the power failure lasted longer than 30 seconds, the

Power Fail Reset option is turned “ON,” the door is

unlocked, and the duration of the power failure is less

than or equal to the time programmed in the Power

Fail Reset option, the START (enter) keypad will flash

until it is pressed and the cycle will restart from the

point it left off.

If the power failure lasted longer than 30 seconds, the

Power Fail Reset option is turned “OFF,” and the door

is unlocked, the START (enter) keypad will flash one

second on and one second off until it is pressed. The

cycle will restart from the point it left off when

START (enter) is pressed.
If the power failure lasted longer than 30 seconds,

lasted longer than the time programmed in the Power

Fail Reset option, and the Power Fail Reset option is

turned “ON,” the control will flash the START (enter)

keypad one (1) second on and one (1) second off.

When the pad is pressed, the cycle will start a delicate

final high spin.

Содержание ST3LXFSP401NW22







































































































Результаты поиска

Содержание ST3LXFSP401NW22

Отзывы:

Похожие инструкции для ST3LXFSP401NW22

Бренды по названию

Популярные бренды

ALLIANCE ST3LXFSP401NW22, Руководство по программированию

Результаты поиска

Содержание ST3LXFSP401NW22

Отзывы:

Похожие инструкции для ST3LXFSP401NW22

Бренды по названию

Популярные бренды