Agilent Technologies G7104A Скачать руководство пользователя страница 77

Страница: 77 / 234

Agilent 1290 Infinity II Flexible Pump User Manual

Error Information

Pump Error Messages

Degasser's pressure limit violation

Error ID: 29220

Pressure too far above the limit.

Seal wash pump was missing when tried to turn on

Error ID: 29223

The seal wash pump has not been detected (while being configured or
detected before)

Probable cause

Suggested actions

Leak in degasser chamber or degasser
tubing.

Please contact your Agilent service
representative.

Defect vacuum pump.

Please contact your Agilent service
representative.

Degasser chamber empty or connected to
air.

Block unused degasser channels.

Probable cause

Suggested actions

Defect cable connection to seal wash pump.

Check cable connection.

Defect seal wash pump motor.

Please contact your Agilent service
representative.

Defective main board.

Please contact your Agilent service
representative.

Содержание G7104A











































































































































































































































Результаты поиска

Содержание G7104A

Отзывы:

Бренды по названию

Популярные бренды

Agilent Technologies G7104A, Руководство пользователя

Результаты поиска

Содержание G7104A

Отзывы:

Бренды по названию

Популярные бренды