manualshive.com logo in svg

Agilent Technologies G7104A, Руководство пользователя

Поделиться
Скачать
Agilent Technologies G7104A Скачать руководство пользователя страница 55

Agilent 1290 Infinity II Flexible Pump User Manual

55

Error Information

6

General Error Messages

 Remote Timeout 

Error ID: 0070

A not- ready condition is still present on the remote input. When an 
analysis is started, the system expects all not- ready conditions (for 
example, a not- ready condition during detector balance) to switch to run 
conditions within one minute of starting the analysis. If a not- ready 
condition is still present on the remote line after one minute the error 
message is generated.

Probable cause

Suggested actions

1

Leak detected in another module with a 
CAN connection to the system.

Fix the leak in the external instrument before 
restarting the module.

2

Leak detected in an external instrument 
with a remote connection to the system.

Fix the leak in the external instrument before 
restarting the module.

3

Shut-down in an external instrument with a 
remote connection to the system.

Check external instruments for a shut-down 
condition.

Probable cause

Suggested actions

1

Not-ready condition in one of the 
instruments connected to the remote line.

Ensure the instrument showing the not-ready 
condition is installed correctly, and is set up 
correctly for analysis.

2

Defective remote cable.

Exchange the remote cable.

3

Defective components in the instrument 
showing the not-ready condition.

Check the instrument for defects (refer to the 
instrument’s documentation).

Содержание G7104A











































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды