manualshive.com logo in svg

Agilent Technologies G7104A, Руководство пользователя

Поделиться
Скачать
Agilent Technologies G7104A Скачать руководство пользователя страница 226

226

Agilent 1290 Infinity II Flexible Pump User Manual

12

Appendix

Waste Electrical and Electronic Equipment Directive

Waste Electrical and Electronic Equipment Directive

Abstract

The Waste Electrical and Electronic Equipment (WEEE) Directive 
(2002/96/EC), adopted by EU Commission on 13 February 2003, is 
introducing producer responsibility on all electric and electronic 
appliances starting with 13 August 2005.

N O T E

This product complies with the WEEE Directive (2002/96/EC) marking requirements. The 
affixed label indicates that you must not discard this electrical/electronic product in 
domestic household waste.

Product Category: 

With reference to the equipment types in the WEEE Directive Annex I, this product is 
classed as a Monitoring and Control Instrumentation product.

N O T E

Do not dispose of in domestic household waste

To return unwanted products, contact your local Agilent office, or see 

www.agilent.com

 for 

more information.

Содержание G7104A











































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды