manualshive.com logo in svg

Agilent Technologies G7104A, Руководство пользователя

Поделиться
Скачать
Agilent Technologies G7104A Скачать руководство пользователя страница 202

202

Agilent 1290 Infinity II Flexible Pump User Manual

11

LAN Configuration

Automatic configuration with Bootp

How BootP Service Works

When an instrument is powered on, an LAN Interface in the instrument 
broadcasts a request for an IP address or host name and provides its 
hardware MAC address as an identifier. The Agilent BootP Service 
answers this request and passes a previously defined IP address and host 
name associated with the hardware MAC address to the requesting 
instrument.

The instrument receives its IP address and host name and maintains the 
IP address as long as it is powered on. Powering down the instrument 
causes it to lose its IP address, so the Agilent BootP Service must be 
running every time the instrument powers up. If the Agilent BootP Service 
runs in the background, the instrument will receive its IP address on 
power- up.

The Agilent LAN Interface can be set to store the IP address and will not 
lose the IP address if power cycled.

Situation: Cannot Establish LAN Communication

If a LAN communication with BootP service cannot be established, check 
the following on the PC:

•

Is the BootP service started? During installation of BootP, the service is 
not started automatically.

•

Does the Firewall block the BootP service? Add the BootP service as an 
exception.

•

Is the LAN Interface using the BootP- mode instead of "Using Stored" or 
"Using Default" modes?

Содержание G7104A











































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды