manualshive.com logo in svg

Agilent Technologies G7104A, Руководство пользователя

Поделиться
Скачать
Agilent Technologies G7104A Скачать руководство пользователя страница 214

214

Agilent 1290 Infinity II Flexible Pump User Manual

11

LAN Configuration

Manual Configuration

6

Change the IP address (in this example 134.40.27.99) and type “/” to list 
current settings.

Figure 41

Telnet - Current settings in "Using Stored" mode

information about the LAN interface
MAC address, initialization mode
Initialization mode is Using Stored
active TCP/IP settings
TCP/IP status - here ready
connected to PC with controller software (e.g. Agilent 
ChemStation), here not connected

Figure 42

Telnet - Change IP settings

change of IP setting to 
Initialization mode is Using Stored
active TCP/IP settings
stored TCP/IP settings in non-volatile memory

connected to PC with controller software (e.g. Agilent 
ChemStation), here not connected

Содержание G7104A











































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды