manualshive.com logo in svg

Agilent Technologies G7104A, Руководство пользователя

Поделиться
Скачать
Agilent Technologies G7104A Скачать руководство пользователя страница 59

Agilent 1290 Infinity II Flexible Pump User Manual

59

Error Information

6

General Error Messages

Fan Failed

Error ID: 0068

The cooling fan in the module has failed. 

The hall sensor on the fan shaft is used by the main board to monitor the 
fan speed. If the fan speed falls below a certain limit for a certain length 
of time, the error message is generated.

Depending on the module, assemblies (e.g. the lamp in the detector) are 
turned off to assure that the module does not overheat inside.

Leak

Error ID: 0064

A leak was detected in the module.

The signals from the two temperature sensors (leak sensor and 
board- mounted temperature- compensation sensor) are used by the leak 
algorithm to determine whether a leak is present. When a leak occurs, the 
leak sensor is cooled by the solvent. This changes the resistance of the 
leak sensor which is sensed by the leak- sensor circuit on the main board.

Probable cause

Suggested actions

1

Fan cable disconnected.

Please contact your Agilent service 
representative.

2

Defective fan.

Please contact your Agilent service 
representative.

3

Defective main board.

Please contact your Agilent service 
representative.

Probable cause

Suggested actions

1

Loose fittings.

Ensure all fittings are tight.

2

Broken capillary.

Exchange defective capillaries.

Содержание G7104A











































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды