manualshive.com logo in svg

Agilent Technologies G7104A, Руководство пользователя

Поделиться
Скачать
Agilent Technologies G7104A Скачать руководство пользователя страница 72

72

Agilent 1290 Infinity II Flexible Pump User Manual

6

Error Information

Pump Error Messages

Pump drive error

Error ID: 29212, 29213

The pump drive failed during calibration.

•

Parameter: 1 – 2 referring to pump drive

Maximum stroke is too short

Error ID: 29203

The maximum stroke is too short.

During initialization the pump defines the operation position of the pump 
drives and therefore the pistons. First the pump drive moves backwards to 
find a mechanical stop within the ball screw. Afterwards, pistons move 
forwards for finding the maximum available stroke volume. These values 
are expected within a pre- defined range. "Maximum stroke too short" 
means that the outer drive position is too close. This can be caused by a 
drive initialization without pump head  or  if  the  pump  head  has  not  been 
installed properly (screws are loose).

•

Parameter: 1 – 2 referring to pump drive

Probable cause

Suggested actions

1

Pump drive encoder is defect.

Please contact your Agilent service 
representative.

Probable cause

Suggested actions

1

Wiper shifted

Please contact your Agilent service 
representative.

2

Pump head blocks piston movement

Replace, clean or repair pump head.

3

Pump drive motor is mechanically blocked.

Please contact your Agilent service 
representative.

Содержание G7104A











































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды