Agilent Technologies G7104A Скачать руководство пользователя страница 63

Страница: 63 / 234

Agilent 1290 Infinity II Flexible Pump User Manual

Error Information

Pump Error Messages

Quaternary pump shutdown during analysis

Error ID: 29199

The quaternary pump has been shut down by the control software or
control module during an analysis.

•

Parameter: 0 for off, 1 for standby.

Reading the pump encoder tag failed

Error ID: 29201

Reading the pump encoder tag has failed.

•

Parameter: 1 – 2 referring to pump drive

Probable cause

Suggested actions

Pump has been shut down.

Restart pump.

Probable cause

Suggested actions

Defect connection between encoder and
main board.

Please contact your Agilent service
representative.

Missing or defect tag Defect connection
between tag and encoder.

Please contact your Agilent service
representative.

Содержание G7104A











































































































































































































































Результаты поиска

Содержание G7104A

Отзывы:

Бренды по названию

Популярные бренды

Agilent Technologies G7104A, Руководство пользователя

Результаты поиска

Содержание G7104A

Отзывы:

Бренды по названию

Популярные бренды