manualshive.com logo in svg

Agilent Technologies G7104A, Руководство пользователя

Поделиться
Скачать
Agilent Technologies G7104A Скачать руководство пользователя страница 180

180

Agilent 1290 Infinity II Flexible Pump User Manual

10

Hardware Information

Interfaces

•

CAN connectors as interface to other modules

•

LAN connector as interface to the control software

•

RS- 232C as interface to a computer

•

USB (Universal Series Bus) as interface to a computer

•

REMOTE connector as interface to other Agilent products

•

Analog output connector(s) for signal output

 Overview Interfaces 

CAN

The CAN is inter- module communication interface. It is a 2- wire serial 
bus system supporting high speed data communication and real- time 
requirement.

LAN

The modules have either an interface slot for an LAN card (e.g. Agilent 
G1369B/C LAN Interface) or they have an on- board LAN interface (e.g. 
detectors G1315C/D DAD and G1365C/D MWD). This interface allows the 
control of the module/system via a PC with the appropriate control 
software. Some modules have neither on- board LAN nor an interface slot 
for a LAN card (e.g. G1170A Valve Drive or G4227A Flex Cube). These are 
hosted modules and require a Host module with firmware B.06.40 or later 
or with additional G1369C LAN Card. 

N O T E

If an Agilent detector (DAD/MWD/FLD/VWD/RID) is in the system, the LAN should be 
connected to the DAD/MWD/FLD/VWD/RID (due to higher data load). If no Agilent 
detector is part of the system, the LAN interface should be installed in the pump or 
autosampler.

Содержание G7104A











































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды