Advanced Instruments 4C3 Скачать руководство пользователя страница 95

Страница: 95 / 139

g. At

“Stir/Freeze Test”

, press START. The display will change

“[stir] [freeze]”

h. At

“[stir] [freeze]”

, a freeze pulse will occur each time the

button is pressed. Watch the tip of the stir/freeze wire and press

. The freeze-pulse vibration should produce a loud

“

buzz

”

. If

properly adjusted as recommended in section 5, the stir/freeze

wire should vibrate principally fore and aft and should never

strike the probe.

i. Manually move the operating head to a position slightly for-

ward of the probe wipers, such that the stir/freeze wire vibration

will be unimpeded by the wipers and clearly visible in front of

the probe.

Watch the stir/freeze wire vibrate as you press

again. The

freeze-pulse vibration blur at the very tip of the stir/freeze wire

should span at least 1/2

”

or 13 mm for one second, then cease.

If the freeze vibration is inadequate, do not proceed further but

refer the problem to a qualified service person with a 4C3 ser-

vice manual or telephone for Hot-Line® service as recommend-

ed in Chapter 5, Section C.

If the freeze vibration is adequate, check and adjust the stir

vibration amplitude as follows:

Troubleshooting & Service

Figure 11:

Probe and Stir/Freeze Wire Alignment

Содержание 4C3












































































































































Результаты поиска

Содержание 4C3

Отзывы:

Бренды по названию

Популярные бренды

Advanced Instruments 4C3, Руководство пользователя

Результаты поиска

Содержание 4C3

Отзывы:

Бренды по названию

Популярные бренды