Advanced Instruments 4C3 Скачать руководство пользователя страница 124

Страница: 124 / 139

102

The Advanced

Model 4C3 User’s Guide

2. Knows of no defects in design or mate-

rials which may cause bodily injury.

3. Will endeavor to advise the user of

changes or improvements in the instru-

ment as they are developed, so that

the user may take steps to improve the

safety and performance of his equip-

ment throughout its useful life.

4. Will replace or repair equipment

according to the guarantee on the

attached warranty.

5. Will cooperate closely in common

defense of any accident involving this

equipment, or third-party suit against

the user or operating personnel, if

advised immediately by the user of the

occurrence of any accident.

THE USER WARRANTS

THAT:

1. The instrument will be used reason-

ably.

2. The instrument will be regularly

maintained according to this manual,

including a log of all service, tests

and repairs performed on the equip-

ment, and records will be kept of all

requests for repair made to Advanced

Instruments where such repairs were

beyond the ability of local service per-

sonnel.

3. The instrument will not be altered

without written approval from

Advanced Instruments.

4. Advanced Instruments will be notified

immediately if any injury occurs in any

association with the instrument and will

be allowed prompt and thorough exam-

ination of the instrument in question.

5. Advanced Instruments will be held

harmless in cases of injury arising (see

definitions below):
a. Beyond the useful life of the

equipment.

b. From unreasonable use.
c. When Advanced Instruments is

not immediately notified of said

injury.

d. From interpretation of results.

DEFINITIONS

“

Useful life

”

is:

a. The same as the depreciation life

in the Internal Revenue Service

guidelines, whether or not the user

actually depreciates the instrument,

but not to exceed 10 years from date

of delivery to the user.

b. Only during the time the equipment

has been maintained on a regular

basis as prescribed by Advanced

Instruments. If the user is in an

area which has no local service,

Advanced Instruments may require

a local service person (understood

to mean the person actually per-

forming the “hands-on” service of

the equipment) to attend and pass a

reasonable maintenance and repair

course.

c. Only during the time when the user

has not altered the equipment in

any way without written approval

from Advanced Instruments.

Содержание 4C3












































































































































Результаты поиска

Содержание 4C3

Отзывы:

Бренды по названию

Популярные бренды

Advanced Instruments 4C3, Руководство пользователя

Результаты поиска

Содержание 4C3

Отзывы:

Бренды по названию

Популярные бренды