Advanced Instruments 4C3 Скачать руководство пользователя страница 44

Страница: 44 / 139

2. Set Sample Bin #

This menu item displays the current sample probe bin

setting and allows the setting to be changed.

CAUTION

Before changing the probe bin setting, the required

setting should be determined by means of the procedure described

in Chapter 5. Changing the bin setting requires recalibration of the

instrument.

“Set Sample Bin #”

, press the START button. The display

will report the current sample bin setting. Compare the sample bin

setting with the sample bin number determined by means of the pro-

cedure described in Chapter 5.

If the current sample bin setting is the same as that determined in

Chapter 5, simply press the STOP button to return to

“Set Sample

Bin #”

. If the bin number is not the same, enter the required bin

number by means of the numeric keypad.

Press ENTER to store the new setting (or STOP to restore the orig-

inal setting).

Recalibrate the instrument as instructed in Chapter 4.

Be sure to record the new sample bin setting in the service log

inside the back cover of the user’s guide.

3. Select Batch

This menu item enables a means of entering an identification num-

ber of up to 4 digits for each batch of tests and the number of sam-

ples in the batch.

When enabled, the 4C3 prompts for the identification number to be

entered via the numeric keypad each time a batch of tests is started

by pressing the START button. The batch identification number is

then displayed and sent to the printer and the communication port,

along with the test results.

The Advanced

Model 4C3 User’s Guide

Содержание 4C3












































































































































Результаты поиска

Содержание 4C3

Отзывы:

Бренды по названию

Популярные бренды

Advanced Instruments 4C3, Руководство пользователя

Результаты поиска

Содержание 4C3

Отзывы:

Бренды по названию

Популярные бренды