Advanced Instruments 4C3 Скачать руководство пользователя страница 125

Страница: 125 / 139

103

Warranty Duties

d. Only during the time when the user

has not loaned, leased or resold the

equipment to any third party.

“

Reasonable use

”

is use:

a. According to the instructions sup-

plied by Advanced Instruments

(assuming English-reading person-

nel or supervision). If neither the

supervisor nor the operator reads

English, the user agrees to obtain

accurate translations of the instru-

ment labels, instructions, user’s

guides and/or manuals provided.

b. Under direct, on-the-job super-

vision of the supervisor or other

professional in charge.

c. In which there are no known

defects or uncorrected repairs.

d. Only for the purpose stated in the

instructions provided with the

instrument.

e. In which the equipment has been

maintained according to the

instructions provided.

“

Immediate notification

”

is:

a. Recognition that time is of the

essence when any accident,

malpractice or product liability

arises which involves Advanced

Instruments equipment.

b. Notification to Advanced

Instruments immediately (the same

day, if possible) in the event of inju-

ry to any person in circumstances

involving Advanced Instruments

equipment in which Advanced

Instruments might be named as a

defendant in any form of litigation.

c. Allowing Advanced Instruments

or its representatives, immediate,

full, and thorough examination of

Advanced Instruments equipment,

and all records pertaining to such

equipment.

Содержание 4C3












































































































































Результаты поиска

Содержание 4C3

Отзывы:

Бренды по названию

Популярные бренды

Advanced Instruments 4C3, Руководство пользователя

Результаты поиска

Содержание 4C3

Отзывы:

Бренды по названию

Популярные бренды