Advanced Instruments 4C3 Скачать руководство пользователя страница 22

Страница: 22 / 139

proportion to the amount of water added.

% DFB (Percent Deviation from Base):

More accurate terminology

for what formerly was called

“

% added water

”

References

1. Prentice, J.H.,

“

Freezing Point Data..

”

, Analyst, 103:1269 (1978).

2. Henningson, R.W,

“

The Freezing Point of Milk Produced in North

America

”

, AOAC 52-142-151 (1969).

“

British Standard Methods for Determination of the Freezing-Point

Depression of Milk

”

, BS3095: Part 2 (1988).

4. Marth, E.H,

“

Assuring the Quality of Milk

”

, J. Dairy Science

64.1017-1022 (1981).

“

British Standard Methods for Determination of the Freezing-Point

Depression of Milk

”

, BS3095: Part 1 (1988).

“

IDF-1S0-A0AC Method

”

Water (Added) in Milk, Thermistor

Method, Section 96LO7, AOAC METHODS, Association of Official

Analytical Chemists, 15th edition (1990).

“

Added Water in Milk

”

, section 19.2 of STANDARD METHODS

FOR THE EXAMINATION OF DAIRY PRODUCTS, American

Public Health Association, 14th edition.

“

Concentrative Properties of Aqueous Solutions

”

beginning on

page D-221 of the CRC HANDBOOK OF CHEMISTRY AND

PHYSICS, 701h Edition, CRC Press, 1989-90.

“

Isotonic Solutions

”

within the Miscellaneous Tables section of the

MERCK INDEX, Merck & Co, Inc., Eleventh Edition, 1989.

xxii

The Advanced

Model 4C3 User’s Guide

Содержание 4C3












































































































































Результаты поиска

Содержание 4C3

Отзывы:

Бренды по названию

Популярные бренды

Advanced Instruments 4C3, Руководство пользователя

Результаты поиска

Содержание 4C3

Отзывы:

Бренды по названию

Популярные бренды