Advanced Instruments 4C3 Скачать руководство пользователя страница 12

Страница: 12 / 139

xii

The Advanced

Model 4C3 User’s Guide

This symbol indicates the presence of alternating current (AC).

This symbol indicates the presence of a fuse.

This symbol indicates the presence of protective earth ground.

General cautions

• This product should be operated only with the type of power source

indicated on the product’s electrical ratings label. Refer to the

installation instructions included with the product.

• If the power cord provided is replaced for any reason or if an alter-

nate cord is used, the cord must be approved for use in the local

country. The power cord must be approved for the product’s listed

operating voltage and be rated at least 20% greater than the ampere

ratings marked on the product’s electrical ratings label. The cord

end that connects to the product must have an IEC 60320 connector.

•  Plug the product into an approved grounded electrical outlet.
•  Do not disable the power cord’s grounding plug.
•  If an extension cord or power strip is used, make sure that the cord

or strip is rated for the product, and that the total ampere ratings of

all products plugged into the extension cord or strip do not exceed

80% of the cord’s or strip’s rating limit.

• Route power cords so that they will not be walked on, tripped on, or

pinched by items placed upon or against them. Pay particular atten-

tion to the plug, electrical outlet, and the point where the cord exits

the product.

• Do not pull on cords and cables. When unplugging cords or cables,

grasp the corresponding connector.

Содержание 4C3












































































































































Результаты поиска

Содержание 4C3

Отзывы:

Бренды по названию

Популярные бренды

Advanced Instruments 4C3, Руководство пользователя

Результаты поиска

Содержание 4C3

Отзывы:

Бренды по названию

Популярные бренды