Advanced Instruments 4C3 Скачать руководство пользователя страница 74

Страница: 74 / 139

•

Unplug the power cord prior to opening or removing covers, or

else you may be exposed to electric shock, excessive tempera-

tures, or mechanical hazards.

•

Performing service or maintenance not detailed in the User’s

Guide, with or without a Service Manual, should only be done

by a qualified service technician.

•

Never restrict airflow into or out of the product. Occasionally,

check the air vents for blockage.

•

Wipe the exterior of the product with a soft, damp cloth as need-

ed. Using cleaning products other than those specified, may

discolor or damage the finish.

•

If the product requires service for any of the following reasons,

unplug the product from the electrical outlet and refer service to

a qualified service technician.
- The power cord, extension cord, power strip, or power

input module is damaged.

Liquid has been spilled into the interior of the product.

- A foreign object has fallen into the product.
- The product has been dropped or damaged by a falling

object.

- There are noticeable signs of overheating or a burning

odor.

- The product does not operate normally when you follow

the operating procedures.

- The main supply fuse(s) or any internal fuse(s) continually

fail.

•

A discharge of static electricity from contact with the human

body or other conductor may damage system boards or static

sensitive devices. Never perform internal maintenance without

following recommended static protection procedures.

The Advanced

Model 4C3 User’s Guide

Содержание 4C3












































































































































Результаты поиска

Содержание 4C3

Отзывы:

Бренды по названию

Популярные бренды

Advanced Instruments 4C3, Руководство пользователя

Результаты поиска

Содержание 4C3

Отзывы:

Бренды по названию

Популярные бренды