Advanced Instruments 4C3 Скачать руководство пользователя страница 30

Страница: 30 / 139

5. Push the paper in far enough for the end to slightly protrude

from the paper output slot in the printer door.

6. Grasp the protruding tip of paper and gently pull 2-4

”

(8-15 cm)

straight out of the slot in the printer door while, with the other

hand, centering the paper being drawn in.

CAUTION

If the paper is not carefully centered as it is being

drawn into the printer, its edges may fray or tear, caus-

ing the paper to jam in the printer.
If the printer paper becomes jammed under the print

head, a protective circuit will shut off the printer with-

out deactivating the display or the rest of the instru-

ment.
To reactivate the printer, shut off the 4C3. Clear the

paper jam and turn the power back on. If the paper jam

has been successfully cleared, the instrument will com-

plete the power-up cycle described in section H and

reactivate the printer.

7. Insert the paper-roll holder into the paper roll, center it and drop

the roller ends into the roller slots (see figure 6).

8. Pull enough paper through the printer to take up any slack

between the paper roll and the printer.

The Advanced

Model 4C3 User’s Guide

Figure 6:

Loading Printer Paper

Содержание 4C3












































































































































Результаты поиска

Содержание 4C3

Отзывы:

Бренды по названию

Популярные бренды

Advanced Instruments 4C3, Руководство пользователя

Результаты поиска

Содержание 4C3

Отзывы:

Бренды по названию

Популярные бренды