Advanced Instruments 4C3 Скачать руководство пользователя страница 41

Страница: 41 / 139

K. Setup

Your 4C3 has been setup at the factory for normal operation, but

the SETUP menu may be required for changing the date and time or

customizing the setup parameters for your own individual needs.

NOTES

The supervisor/operator keyswitch must

be in the Supervisor position to enable the use of the

SETUP menu. If the SETUP button is pressed while

the supervisor/operator keyswitch is in the operator

position, a

“Supervisor Key Needed; Press

Stop to Continue”

message will be displayed.

b. The instrument setup is stored in firmware which can

easily be updated at the factory to incorporate possi-

ble additional setup items or refinements. The follow-

ing list includes all currently implemented setup func-

tions in the order in which they appear in the SETUP

menu; however, the order in which they appear may

change slightly if the firmware is later updated to

include additional SETUP items.

The operating parameters that may be checked and set via the setup

menu are listed in table 5.

Enter SETUP, if required, by pressing the SETUP button. When

SETUP is pressed, the display will change to

“Select Setup

Item”

There are two ways to select a SETUP menu item, direct selection

and sequential selection, described as follows:

0. Select Setup Item

This menu item is displayed first when SETUP is pressed, and

allows either direct selection or sequential selection of a menu

item.

Installation & Setup

Содержание 4C3












































































































































Результаты поиска

Содержание 4C3

Отзывы:

Бренды по названию

Популярные бренды

Advanced Instruments 4C3, Руководство пользователя

Результаты поиска

Содержание 4C3

Отзывы:

Бренды по названию

Популярные бренды