![background image](http://html.mh-extra.com/html/abb/acs-800-series/acs-800-series_firmware-manual_314164.webp)
Actual signals and parameters
164
11.04
EXT REF1 MINIMUM Defines the minimum value for external reference REF1 (absolute value).
Corresponds to the minimum setting of the source signal used.
0 … 18000 rpm
Setting range in rpm (Hz if parameter
is SCALAR).
Example:
Analogue input AI1 is selected as the reference source (value of
parameter
is AI1). The reference minimum and maximum correspond
the AI minimum and maximum settings as follows:
Note:
If the reference is given through fieldbus, the scaling differs from that of
an analogue signal. See chapter
for more information.
1 … 18000
11.05
EXT REF1 MAXIMUM Defines the maximum value for external reference REF1 (absolute value).
Corresponds to the maximum setting of the used source signal.
0 … 18000 rpm
Setting range (Hz if value of parameter
See parameter
EXT REF1 MINIMUM.
1 … 18000
11.06
EXT REF2 SELECT
Selects the signal source for external reference REF2. REF2 is a
- speed reference in percent of the Absolute Maximum Speed if parameter
- frequency reference in percent of the Absolute Maximum Frequency if
parameter
= SCALAR.
Note
: In M/F configuration, EXT2 should be used for M/F mode and EXT1 for
stand-alone mode.
KEYPAD
See parameter
EXT REF1 SELECT.
1
AI1
See parameter
Note:
If the signal is bipolar (±10 V DC), use the selection AI1 BIPOLAR. The
selection AI1 ignores the negative signal range.
2
AI2
See parameter
3
AI3
See parameter
4
AI1/JOYST
See parameter
5
AI2/JOYST
See parameter
6
DI3U,4D(R)
See parameter
7
DI3U,4D
See parameter
8
DI5U,6D
See parameter
9
COMM. REF
See parameter
10
FAST COMM
See parameter
Note:
In addition to the conditions stated for parameter 11.03, the drive must
be in Torque control, and this reference used as a torque reference by the
Follower drive. Otherwise this selection works like COMM.REF.
11
Index
Name/Selection
Description
FbEq
AI1 Range
EXT REF1 Range
Minimum setting for AI1
Maximum setting for AI1
Minimum reference
Maximum reference
13.01
13.02
11.04
11.05
Содержание ACS 800 Series
