manualshive.com logo in svg

ZyXEL Communications ZyXEL Prestige 310, User Manual

Share
Download
ZyXEL Communications ZyXEL Prestige 310 User Manual Download Page 60

Prestige 310 Broadband Sharing Gateway

Remote Node Setup

4-1

Chapter 4

Remote Node Setup

This chapter shows you how to configure a remote node.

A remote node is required for placing calls to a remote gateway.  A remote node represents both the remote
gateway and the network behind it across a WAN connection.  Note that when you use menu 4 to set up
Internet access, you are actually configuring a remote node. We will show you how to configure the
following menus:

•

 

Menu 11.1 — Remote Node Profile

•

 

Menu 11.3 — Remote Node Network Layer Options

•

 

Menu 11.5 — Remote Node Filter

.

4.1  Remote Node Profile

From the main menu, enter 11 to display 

Menu 11.1 

— 

Remote Node Profile

. There are three variations of

this menu depending on whether you choose Ethernet Encapsulation, PPTP or PPPoE Encapsulation.

4.1.1 Ethernet Encapsulation

Choose the 

Ethernet

 option when the WAN port is used as a regular Ethernet. The first menu 11.1 screen

you see is for 

Ethernet

 Encapsulation shown next.

Figure 4-1 Remote Node Profile for Ethernet Encapsulation

                         Menu 11.1 - Remote Node Profile

     Rem Node Name= ChangeMe

Route= IP

     Active= Yes

     Encapsulation= Ethernet

Edit IP= No

     Service Type= Standard

Session Options:

     Service Name= N/A

  Edit Filter Sets= No

     Outgoing:
       My Login= N/A
       My Password= N/A
       Server IP= CHAP/PAP

Press ENTER to Confirm or ESC to Cancel.

Summary of Contents for ZyXEL Prestige 310








































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands