manualshive.com logo in svg

ZyXEL Communications ZyXEL Prestige 310, User Manual

Share
Download
ZyXEL Communications ZyXEL Prestige 310 User Manual Download Page 129

Prestige 310 Broadband Sharing Gateway

9-4

System Information and Diagnosis

Figure 9-3 Menu 24.2 — System Information and Console Port Speed

9.2.1 System Information

System Information gives you information about your system as shown below. More specifically, it gives
you information on your routing protocol, country code, Ethernet address, IP address, etc.

 Figure 9-4 Menu 24.2.1 System Maintenance — Information

Table 9-2 Fields in System Maintenance

FIELD

 DESCRIPTION

Name

This is the Prestige's system name + domain name assigned in menu
1, for example, System Name= Prestige;  Domain Name= 

zyxel.com

Name= P310.

zyxel.com

Routing

Refers to the routing protocol used.

ZyNOS F/W Version

Refers to the version of ZyXEL's Network Operating System software.

                    Menu 24.2 - System Information and Console Port Speed

1. System Information
2. Console Port Speed

                                Please enter selection:

                                                             

Menu 24.2.1 - System Maintenance - Information

Name: P310.www.zyxel.com
Routing: IP
ZyNOS F/W Version: V2.51 | 2/17/2000

LAN
  Ethernet Address: 00:a0:c5:21:8c:a2
  IP Address: 192.168.1.10
  IP Mask: 255.255.255.0
  DHCP: Server

                                 Press ESC or RETURN to Exit

Summary of Contents for ZyXEL Prestige 310








































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands