manualshive.com logo in svg

ZyXEL Communications ZyXEL Prestige 310, User Manual

Share
Download
ZyXEL Communications ZyXEL Prestige 310 User Manual Download Page 52

Prestige 310 Broadband Sharing Gateway

Internet Access

3-7

FIELD

DESCRIPTION

EXAMPLE

Version Press the [SPACE BAR] to select the RIP version.

Options are 

RIP-1

,

 RIP-2B 

or

 RIP-2M

.

RIP-1

(default)

Multicast

IGMP (Internet Group Multicast Protocol) is a session-layer protocol
used to establish membership in a Multicast group. The Prestige
supports both IGMP version 1 (

IGMP-v1

) and 

IGMP-v2

. Press the

[SPACE BAR] to enable IP Multicasting or select 

None

 (default) to

disable it.

None

Edit IP Alias

The Prestige supports three logical LAN interfaces via its single
physical Ethernet interface with the Prestige itself as the gateway for
each LAN network. Press the [SPACE BAR] to select 

Yes

, then

press [ENTER] to display menu 3.2.1

Yes

When you have completed this menu, press [ENTER] at the prompt [Press ENTER to Confirm…] to save
your configuration, or press [ESC] at any time to cancel.

3.2.1 IP Alias Setup

Use menu 3.2 to configure the first network and move the cursor to the 

Edit

 

IP

 

Alias

 field and press

[

SPACE

 

BAR

] to choose 

Yes

 and press [

ENTER

] to configure the second and third network.

Pressing [

ENTER

] opens 

Menu 3.2.1 — IP Alias Setup

, as shown next.

Figure 3-5 Menu 3.2.1 — IP Alias Setup

Follow the instructions in the following table to configure IP Alias parameters.

Menu 3.2.1 - IP Alias Setup

                    IP Alias 1= No
                      IP Address= N/A
                      IP Subnet Mask= N/A
                      RIP Direction= N/A
                        Version= N/A
                      Incoming protocol filters= N/A
                      Outgoing protocol filters= N/A
                    IP Alias 2= No
                      IP Address= N/A
                      IP Subnet Mask= N/A
                      RIP Direction= N/A
                        Version= N/A
                      Incoming protocol filters= N/A
                      Outgoing protocol filters= N/A

                     Enter here to CONFIRM or ESC to CANCEL:

Press Space Bar to Toggle.

Summary of Contents for ZyXEL Prestige 310








































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands