manualshive.com logo in svg

ZyXEL Communications ZyXEL Prestige 310, User Manual

Share
Download
ZyXEL Communications ZyXEL Prestige 310 User Manual Download Page 136

Prestige 310 Broadband Sharing Gateway

System Information and Diagnosis

9-11

9.4 Diagnostic

The diagnostic facility allows you to test the different aspects of your Prestige to determine if it is working
properly. Menu 24.4 allows you to choose among various types of diagnostic tests to evaluate your system,
as shown next.

Figure 9-10 Menu 24.4 — System Maintenance — Diagnostic

Follow the procedure below to get to 

Menu 24.4 — System Maintenance — Diagnostic.

Step 1. 

From the main menu, enter 24 to open 

Menu 24 — System Maintenance

.

Step 2. 

From this menu, enter 4 to display 

Menu 24.4 — System Maintenance — Diagnostic

.

9.4.1 WAN DHCP

DHCP functionality can be enabled on the LAN or WAN as shown in 

Figure 9-11

. The Prestige can act

either as a WAN DHCP client (

IP Address Assignment

 field in menu 4 or menu 11.3 is 

Dynamic

 and the

Encapsulation

 field in menu 4 or menu 11 is 

Ethernet

) or “none”, i.e., you have a static IP.  The WAN

Release and Renewal fields in menu 24.4 conveniently allow you to release and/or renew the assigned WAN
IP address, subnet mask and default gateway in a fashion similar to winipcfg.

Menu 24.4 - System Maintenance - Diagnostic

                  TCP/IP

1.

 

Ping Host

2.

 

WAN DHCP Release

3.

 

WAN DHCP Renewal

4.

 

Internet Setup Test

                  System
                  11. Reboot System

                  Enter Menu Selection Number:

                  Host IP Address= N/A

Summary of Contents for ZyXEL Prestige 310








































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands