manualshive.com logo in svg

Zycoo UC510, User Manaual, Page: 82 / 84

Share
Download
Zycoo UC510 User Manaual Download Page 82

 

 
Copyright © ZYCOO All Rights Reserved                                                                                               

81

 / 

84

 

 

ra0: Wi-Fi interface 
LAN: includes LAN1 ~LAN4 by default 
 
 

5.1.5  Upgrade 

Upgrade is used to update your system as required. 
 
The system can be upgraded from this

【

Upgrade

】

page via uploading package. 

 

Click

【

Administration

】

【

Upgrade

】

：

 

 

Select  the  upgrade  file  and  then  click  the  "Upload"  button,  the  system  will  be  automatically 
upgraded. 

Notice: 

All functions will not be available during system upgrade; please prepare before operation. 
Please do not change the updated file in case of any failure of the upgrade.

 

 

5.1.6  Backup & Restore 

The system settings including IVR prompt, music files on hold, and Wi-Fi router configurations can 
be backed up in case of any failure of the system. Within the backup files, you can easily restore 
the system. 

Summary of Contents for UC510





















































































Reviews:

No comments