Zycoo UC510 User Manaual Download Page 65 | Manualshive

Page: 65 / 84

Zycoo UC510 User Manaual Download Page 65

Copyright © ZYCOO All Rights Reserved

64

/

84

Country Code

Choose your country code in the drop-down list

WMM Capable

Enable it to improve wireless multimedia data transmission
performance (such as video or online broadcast). If you are
not familiar with the WMM, please set it to capable.

APSD Capable

Automatic Power Save Delivery. Enable it to save power
when no data is transmitted. This may affect the wireless
network performance. Default is disabled.

4.2.3 Security

The security page allow for configuration of wireless network security/ encryption settings.

Click

【

Router Gateway

】



【

Wireless

】



【

Security

】

to show as below:

Reference

:

Item

Explanation

Policy

Select Disabled, Allow, Reject in the drop-down list

Add a station Mac

Here you can add a new MAC address for a Frequency Wi-Fi client .If
Disabled is selected then the access policy is disabled; If Allow is selected
then the MAC access is allowed only to access; If Reject is selected then
all the MAC addresses listed here will be rejected.
You are allowed to add 64 MAC addresses maximum.

Wireless network security/encryption Settings include: security policy and access policy. Security
policy includes 4 modes: OPENWEP, WPA2-PSK, WPA-PSK/WPA2-PSK, WPA1/WPA2.

WEP

: Wired Equivalent Privacy, which is a security algorithm for IEEE 802.11 wireless networks.

WEP uses the stream cipher RC4 for confidentiality, and the CRC-32 checksum for integrity.
OPENWEP is one way of WEP.

«
...
63
64
65
66
67
...
»

Summary of Contents for UC510





















































































Reviews:

No comments