Zycoo UC510 User Manaual Download Page 37

Page: 37 / 84

international call using trunks connected to the PBX. By calling the DISA number, after PIN
authentication, the caller hears dial tone and can dial the call.

Please configure as below.

Click

【

Advance

】



【

DISA

】

Click

【

New DISA

】

to create a new DISA

Reference

Item

Explanation

Name

Define a name for DISA.

PIN Set

User will be prompted to input this number when PIN
Authentication is needed.

Record in CDR

Check to record.

Response Timeout(sec)

The maximum time for waiting before hanging up if the dialed
number is incomplete or invalid. Default is 10 seconds

Digit Timeout(sec)

The maximum interval time between digits when typing
extension number. Default is 5 seconds.

Extension for this
DISA(Optional)

If you want to access DISA by dialing an extension, you can
define an extension number for this DISA.

Select DialPlan

Select the DialPlan for this DISA.

Summary of Contents for UC510




















































































Search results

Summary of Contents for UC510

Reviews:

Zycoo UC510, User Manaual, Page: 37 / 84

Search results

Summary of Contents for UC510

Reviews: