Zycoo UC510 User Manaual Download Page 80

Page: 80 / 84

Item

Explanation

Password

Input new password

Confirm Password

Confirm the new password

Current Time

Synchronize the current time

Time Zone

Select your time zone

NTP Server

Input the NTP server to synchronize the time

NTP synchronization (Hours)

The interval of NTP synchronization. Default is 24 hours

Dynamic DNS Provider

Support Dyndns.org / freedns.afraid.org/ www.zoneedit.com /

www.no-ip.com

Account

Input the account which is applied from DNS provider

Password

Input the password which is applied from DNS provider

DDNS

Input the host which is applied from DNS provider

After settings, click "Apply" to activate.

5.1.2 Activate Configuration

Activate Configuration is only for Wi-Fi router here. PBX settings is separate and not included
here.
There are two ways to activate configurations:
a)

After settings for a function of router, press “Activate” at the bottom of the relative page to
activate the settings;

Click

【

Administration

】



【

Activate Configuration

】

to enter the page as below:

Notice:

During this activation period, network will restart and disconnect in a short time; please prepare
before this operation.

5.1.3 Reset &Reboot

Reset will make the system reset to factory settings, and reboot will make the system restart.

Click

【

Administration

】



【

Reset & Reboot

】

to show the page as below:

Summary of Contents for UC510




















































































Search results

Summary of Contents for UC510

Reviews:

Zycoo UC510, User Manaual, Page: 80 / 84

Search results

Summary of Contents for UC510

Reviews: