manualshive.com logo in svg

Zycoo UC510, User Manaual, Page: 12 / 84

Share
Download
Zycoo UC510 User Manaual Download Page 12

 

 
Copyright © ZYCOO All Rights Reserved                                                                                               

11

 / 

84

 

 

Agent 

Set this extension user as agent.   

NAT 

Check  this  option if  extension user  or  the  phone  is  located  behind  the 
router. 

Pickup Group 

Select the Pickup Group which the extension user belongs to. 

Mobility Extension 

If  this  option  is  checked,  you  must  set  mobile  extension  number.  User 
can make calls to the PBX server with this mobile number, and have all 
rights  of  this  extension,  e.g.:  Outbound  Call,  Internal  Call,  or  listen  to 
voicemail.   

Transport 

Select the Transport Protocol: UDP, TCP 

DTMF Mode 

Default DTMF is rfc2833. It can be changed if necessary. 

Video Call 

Check  to  enable  video  calling  for  this  extension  and  select  the  video 
codecs you require. 

Permit IP 

Set  device  IP  address  or  subnet  permitted  to  register  extensions  with 
the PBX. 
E.g.:192.168.1.77/255.255.255.255  or  192.168.10.0/255.255.255.0. 
Devices with other IP addresses are not allowed to register extension to 
the PBX. 

Audio Codecs 

Select what audio codecs you require. 

 

3.1.2  Trunk 

If  you  want  to  set  up  an  outbound  route  connected  to  the  PSTN  (Public  Switch  Telephone 
Network) or VoIP provider, please configure on this page: 

Click

【

Extensions

】

【

Trunks

】

: 

 

UC510/520 supports two kinds of trunks for your choice: VoIP Trunk and FXO trunk. 

 
VoIP Trunks 

Summary of Contents for UC510





















































































Reviews:

No comments