Zycoo UC510 User Manaual Download Page 75

Page: 75 / 84

Basic information configuration(Max. 32 Open Ports)

Current Open Ports in system

Current Open Ports in system is listed here. Click

【

Delete Selected

】

to delete selected Open Port.

4.3.4 Port Forward

(NAT)

Port forward allows remote computers (for example, computers on the Internet) to connect to a
specific computer or service within a private local-area network (LAN).

Packet Forwarding Settings:

Click

【

Firewall

】



【

Port Forward

】

: from the following diagram, visit port 222 from WAN, the data

will be forwarded to the client 192.168.10.5.

Reference

Item

Explanation

Private IP Address

Private destination IP address that packet forwarded to.
E.g.: 192.168.10.5

Port Range

Destination port range that packet forwarded. E.g.: 222

Protocol

TCP&UDP/TCP/UDP

Comment

Annotation for this port forwarding

Port Forwarding

Click

【

Apply

】

and save settings. Basic information configuration(Max.32 port forwarding rules).

Current Port Forwarding in system

Summary of Contents for UC510




















































































Search results

Summary of Contents for UC510

Reviews:

Zycoo UC510, User Manaual, Page: 75 / 84

Search results

Summary of Contents for UC510

Reviews: