manualshive.com logo in svg

Zycoo UC510, User Manaual, Page: 71 / 84

Share
Download
Zycoo UC510 User Manaual Download Page 71

 

 
Copyright © ZYCOO All Rights Reserved                                                                                               

70

 / 

84

 

 

automatically.

 

 

WPS Reference: 

Item 

Description 

WPS Current Status 

WPS Current Status. Idle=Inactive 

WPS Configured 

Yes: WPS is configured   

WPS SSID 

SSID, can be set in the Basic screen Network Name (SSID) 

WPS Auth Mode 

WPS Authentication Mode; a kind of security mode, same as 
the “Security” menu. 

WPS Encryption Type 

WPS Encryption Type 

WPS Default Key Index 

Default key index of WPS 

WPS Key(ASCII) 

Wi-Fi password 

AP PIN 

PIN code for wireless clients to connect to AP via WPS 

WPS mode 

Support  PIN(Personal  Identification  Number)  and  PBC(Push 
Button Configuration) 
PIN: Click “Apply” after inputting PIN.WPS Current Status will 
display the connection is successful after WPS is connected; 
PBC:  Click  “Apply”  after  selecting  PBC,  or  quickly  click  the 
Turbo button on the router, wireless clients can connect. 

WPS Status 

Status about wireless clients connect to the WPS, which is in 
accordance with WPS Current Status. 

 
 

4.3 

Firewall 

4.3.1  MAC/IP/Port Filter 

Any  connection  request  from  terminals  can  be  controlled  by  the  filter  feature  according  to  the 
defined  rule  parameters.  Filtering  based  on  MAC,  source  IP  and  source  port  can  prevent  the 
terminal from unauthorized network connections.   
 
Set MAC/IP/Port filter: 

Click

【

Firewall

】

【

MAC/IP/Port Filter

】

: take the following diagram as example, the host with 

192.168.10.0/24 is allowed to surf internet, but the host with 192.168.10.5 is rejected to connect 
network. 

Summary of Contents for UC510





















































































Reviews:

No comments