Zycoo UC510 User Manaual Download Page 38 | Manualshive

Page: 38 / 84

Zycoo UC510 User Manaual Download Page 38

Copyright © ZYCOO All Rights Reserved

37

/

84

3.3.6 Follow Me

This feature allows callers to automatically be forwarded to one or more internal extensions
and/or one or more external phone numbers when the call is not answered at the primary
extension.

Please configure as below.
Click

【

Advanced

】



【

Follow Me

】



【

New Follow Me

】

:

Select an extension, set the ring duration, and add the numbers in the Follow Me List;

【

Save

】

and

【

Activate

】

.

List Format: Extension Number, Ring Duration
E.g.: 806,30

808,20

806 rings, after 30 seconds, the call is going to 808

3.3.7 PIN Sets

This feature allows an administrator to specify a list of PIN codes in a PIN Set.  These PIN codes
can  then  be  used  to  secure  an  Outbound  Call  Route,  ensuring  that  users  must  enter  the  PIN
selected to be able to make an outbound call (e.g. for long distance or international calling).

Please configure as below.

Click

【

Advanced

】



【

PIN Sets

】



【

New PIN Set

】

:

«
...
36
37
38
39
40
...
»

Summary of Contents for UC510





















































































Reviews:

No comments