Zycoo UC510 User Manaual Download Page 18

Page: 18 / 84

Reference:

Item

Explanation

Port

Select the port

Label

Set a label for the port. Incoming calls from this port will display the
specified label.

Destination

Incoming calls will be answered by the specified destination.
(extension user, call queue or IVR etc)

Number DIDs

If you want to set the destination of inbound calls through VoIP and E1/T1 Trunks based on the
incoming DNIS (dialed number or DID), you can specify the DID and destination (user extension,
queue or IVR, etc) from the following diagram.

Click

【

Number DID

】



【

New Number DID

】

Reference:

Item

Explanation

DID Number

Set DID Number

Destination

Incoming calls will be answered by the specified destination
(extension user, call queue or IVR etc)

DOD Settings

To configure outbound calls from user extensions to answer with specified destinations (user

extension, queue, IVR, etc) , please click

【

DOD Settings

】



【

New DOD

】

Summary of Contents for UC510




















































































Search results

Summary of Contents for UC510

Reviews:

Zycoo UC510, User Manaual, Page: 18 / 84

Search results

Summary of Contents for UC510

Reviews: