Zycoo UC510 User Manaual Download Page 60 | Manualshive

Page: 60 / 84

Zycoo UC510 User Manaual Download Page 60

Copyright © ZYCOO All Rights Reserved

59

/

84

4.1.5 IPv6 Setup

Internet Protocol version 6

(

IPv6

) is the latest version of the Internet Protocol(IP), the

communications protocol that provides an identification and location system for IP based devices,
e.g. computer on networks and routes traffic across the Internet.IPv6 is intended to replace IPv4,
which still carries more than 96% of Internet traffic worldwide as of May 2014.

Click

【

Internet

】



【

IPv6

】

：

Select

Static IP Connection

for IPv6 Operation Mode

Reference:

Item

Explanation

IPv6 Operation Mode

Static IP Connection

LAN IPv6 Address / Subnet Prefix
Length

Set IPV6 address and subnet prefix length on LAN

WAN IPv6 Address / Subnet
Prefix Length

Set IPV6 address and subnet prefix length on WAN

Default Gateway

Set default gateway

IPv6 Operation Mode: Select Tunneling Connection(6RD)

Reference:

Item

Explanation

IPv6 Operation Mode

Tunneling Connection(6RD):

ISP 6rd Prefix / Prefix Length

Set ISP 6RD prefix/prefix length

ISP Border Relay IPv4 Address

Set IPv4 address on Broadcast(Layer)

4.1.6 DHCP Client Info

The DHCP client info will displays the information of terminals once they have been assigned IP
address from DHCP server, including hostname, MAC address, IP address and expiration time.

«
...
58
59
60
61
62
...
»

Summary of Contents for UC510





















































































Reviews:

No comments