manualshive.com logo in svg

Zycoo UC510, User Manaual, Page: 17 / 84

Share
Download
Zycoo UC510 User Manaual Download Page 17

 

 
Copyright © ZYCOO All Rights Reserved                                                                                               

16

 / 

84

 

 

Delete[    ]digits prefix 

Define how many digits will be deleted from the dialed number.   
For  example,  user  dialed  94166445775  and  you  selected  to  delete  1 
digit, then 4166445775 is sent out to the trunk. 

Auto-add digit[    ] 

If add digit “9”, when dial 12345, 912345 will be sent.   

 

3.2 

Inbound Control 

3.2.1  Inbound Routes 

Click

【

Inbound Control

】

【

Inbound Routes

】

 

 

 
General 

Distinctive  Ring  Tone

：

mapping  the  custom  ring  tone  file,  e.g.:  Set  distinctive  ring  tone  as 

“External”, the phone will play this ring tone when receiving the call.   

Note: 

The phone must support such feature as well. 

 
Select  all  calls  coming  in  on  a  specific  port  (FXO/VoIP)  and  select  which  destination  (Extension 
User,  IVR,  Queue,  Conference  Bridge,  IVR,  etc)  should answer  those  calls.  Setting  the  label  will 
assign this label to be displayed. 
 

Port DIDs 

To have incoming calls from a PSTN trunk port (FXO trunk) answered by a specific extension user, 
call queue, conference bridge, or IVR, please configure here: 

Click

【

Port DIDs

】

【

New Port DIDs

】

: 

Summary of Contents for UC510





















































































Reviews:

No comments