Zycoo UC510 User Manaual Download Page 59 | Manualshive

Page: 59 / 84

Zycoo UC510 User Manaual Download Page 59

Copyright © ZYCOO All Rights Reserved

58

/

84

Reference:

Item

Explanation

Direction

Transmission direction (no need to configure)

Name

Custom define the rule name

Group

Select the corresponding group (or priority group)

Outside IP address

Set outside IP address(or network segment) and corresponding group
subnet mask digits, e.g.: 192.168.10.0/24. Or be null to allow all

outside IP address.

Inside IP address

Set inside IP address(or network segment) and subnet mask digits,
e.g.: 192.168.10.0/24. Or be null to allow all intranet IP.

Packet Length

Set the rule package length, or don’t set. Default is null.

DSCP

DSCP(Differential Service Code Point) supports: BE(default)/ AF11/
AF12/ AF13/ AF21/ AF22/ AF23/ AF31/ AF32/ AF33/ AF41/ AF42/
AF43/ EF
Default is null.

Protocol

You can select TCP/UDP/ICMP or null (all protocols use the default IP
address). When TCP or UDP is selected, you must complete the
outside and intranet port range.

Remark DSCP as

Optional. You can reset DSCP for QoS or do not change. Default is “Do
Not change”

Click

【

Add upload rules

】

to add the rule(at most 32 rules).

It is the same process to add download rule in “QoS Download Group Settings”.

Note:

LAN IP 192.168.1.1 of the UC510 is not included in QoS settings. QoS settings is only for

client devices connected to LAN of UC510.

«
...
57
58
59
60
61
...
»

Summary of Contents for UC510





















































































Reviews:

No comments